How to maintain the cutting machine?–Oriole

How to maintain the cutting machine?

Here are some details about the maintenance of  the cutting machine after using it.

  • Above all,clean.

Firstly,we need to clean the attached dust and cut slag on the surface of the equipment.

A fiber laser cutting machine.

A fiber  laser cutting.

Secondly,clean up the water in the A/C storage tank.

Thirdly,cleaning waste scraps and debris in waste trailers.

More over,clean the dust on the A/C dust cover net and the water cooler dust cover net.

Fifthly,clean the water tank of the water cooler.

Last but not least,clean the surface of the cutting head and focus on cleaning the cooling water pipe joint, auxiliary gas joint, protective lens window, QBH/QCS joint and other parts.

  • What’s more,check.

Firstly,check the joints of the capacitor signal module (at the cutting head) to confirm that the fastening is intact and there is no looseness.

Secondly,equipment homing(including X, Y and Z axes).

More over,check the lubricating oil level in the lubricating oil pump. If it is not enough, fill it in time.

Fourthly,check the lubrication condition of each shaft slide rail, rack, gear and z-axis screw; and manually add lubricating oil on the upper end surface and the two end surfaces of the guide rail, and the main mechanical linkage end face of the rack, gear and lead screw is evenly distributed. Apply lithium grease. (If there is rust, be sure to remove the rust first.)

Fifthly,check the water pipes of the cooling water pipe to confirm that there is no extrusion, bending, grinding, scratching and water leakage; check the water pipe joints (push-in connectors and ordinary threaded joints) to confirm that the connection is normal and there is no water leakage.

Sixthly,check if the cooling water pressure gauge value is normal.

What’s more,replace the water cooler to circulate cooling water.

At last,check the wiring harness and cable everywhere, and confirm that there are no extrusion, bending, grinding, and scratching. There is no open welding or short circuit or hidden trouble in the welding of the break point and the plug joint.


That is some of the maintenance of  the cutting machine after using it .




The reason to choose fiber laser cleaning machine-Teresa

The reason to choose fiber laser cleaning machine

Popular fiber laser cleaning machine.

Laser cleaning is widely in various industries, such as shipping, auto parts, rubber mould, high-end machine tool, tire mould, rail, environmental protection and other industries.


 Firstly, Non-contact cleaning, without damage to parts matrix.
Secondly, Precise cleaning, with accurate location, precise size and selective cleaning.
Thirdly, No chemical cleaning fluid, no consumables, safe and environmental protection.
Fourthly, Simple operation, the power can be charged, and the automatic cleaning can be realized by hand or with the manipulator.
 Fifthly, Cleaning efficiency is very high and saving time.
Finally, The laser cleaning system is stable and little maintenance requirement. 1.2 Laser cleaning application

Some notes about machine using:

  1. When the laser cleaning machine is working,Do not point the laser output head to the orientation of the person, and do not make the laser output head from illuminating the surface of the high anti-material (such as copper, aluminum, mirror stainless steel and other surface reflective materials).
  1. Wear labor protection articles as required, and wear protective glasses that meet the requirements in the vicinity of the laser beam.
  1. If the laser does not shut down normally, the next opportunity is in the alarm state, which will affect the life of the laser. Life. Check whether the laser function button switches need to reset before starting the machine.

So if you are looking for rust,paint,oil,dust,etc cleaning machine.The laser cleaning machine is more suitable for you now.

It is better to send us  your products sample pictures, then we can help you to make sure the machine can do your work or not.

And if you  have time,you can tell us how many pieces you want to clean,we need to confirm the power.

Any questions,we can have a further discussion. XTLASER will provide you with the best solution~

Contact us.


Skype: xtlaser Teresa

Descriprtions of the handheld fiber laser welding machine.

                                                                                                   Descriprtions of the handheld fiber laser welding machine.


Here are some descriprtions of the handheld fiber laser welding machine.I would like to share with you some features and operation cost of the handheld fiber laser welding machine. It is easy to operate and the maintenance cost is also very low.

First of all,needn’t welding wire.

Compared with the traditional welding, like tig, it doesn’t need to use welding wire.Only when the gap more than 0.5mm, we should use the wire feeder.

Secondly,less quick-wear parts.

The quickly-wear parts for the  machine are only protective lens and copper nozzle.

What’s more,less electricity and gas.

Except the quick-wear parts, the machine also consume electricity and gas.
The power consumption of 1kw machine is 7.5kw/hour at full power situation. In fact, we usually just use 50%-60% power of 1000w to weld the metals.So the power consumption is small.The machine also need to connect with gas, argon or nitrogen.

The gas can isolate the air from the welding plate to prevent the reaction with the air. So the welding surface of the metal plate will be white and beautiful. The gas also can protect the lens from welding dust.

Tips:The price of the gas is different in different counties and regions. If our customers think the cost of the gas is too high,they can use air compressor to produce air gas. But the welding effect will not very good.The welding surface of the metal may be black.So our customers should wipe the surface of the metal with ethyl alcohol.

Last but not least,easy to maintenance.

The machine is very easy to matain.When finish your welding work, turn off the power and clean the welding head, it can make the lifetime of protective lens and copper nozzle longer.


That is all my descriptation.Hope it is helpful for you. If you have any confused of machine,please feel free contact us.

Details of Fiber Laser Marking Machine—Oriole

Details of Fiber Laser Marking Machine

There are many details of fiber laser marking machine I want to discuss in this text.I will talk about the reason why we use fiber laser marking maching,the components of it and how can we use it.

Fiber laser marking

Fiber laser marking

Why we choose laser marking machine?

Firstly,power saving.For one hour working ,a laser marking machine just cost 0.5kw/h.

Scendly,maintenance-free.A laser marking machine can work for one hundred thousand hours in theory with no maintenance.

Thirdly,simple using.It is easy for us to use it to mark.

Fourthly,mini.It just cover a small area.

Fifthly,permanency.The pattern it marked will never fall off.

Sixly,elegant appearance.What the machine marked looks superior.

Elements and respective roles:

A fiber laser marking machine consists a lot of components.Each of them has its own function.Let us see.

Firstly,fiber laser source.The most important part of the machine.It decides the efficiency and strength of the machine.

Scendly,2D galvo head. Control the movement of the laser beam in the plane.

Thirdly,2D F-theta lens.Scanning and focussing is what it is doing.

Fourthly,control board&marking software.Order the machine to finish its work.

Fifthly,computer.Play a role together with control board&marking software.

Sixly,lifting pillar.It is helpful for the  laser marking machine to focus.

Seventhly,2D working table.We can place the object here and then we can focus easyer.

Eighthly,power supply.When the power of a laser marking machine is fine and open ,we can begin our marking.

How to use the fiber laser marking machine to marking something?

Firstly,open the switch of the computer and then open other three switches.

Scendly,sto make sure it will mark the object on the right position scan and focus .

Finally,operate the software of the machine,and then you will get the pattern you want.

Last but not the least,when you finish your work,you also need abide by the rules.You should close the computer first and then close other switches.

Attention:when you operate the machine if happened anything dangerous ,you can use the emergency stop switch as soon as possible.






Features of fiber laser marking -Huda

Features of fiber laser marking

Fiber laser marking machine has many advantages compare with traditional symbol methods (pad printing, coding, electro-erosion, etc.) due to its extraordinary working principle;

First:Non-contact processing

can  print on any regular or irregular surface, and there will be no internal stress on the workpiece;

 Second:Wide range of materials

Can print on materials of different types or hardness, such as metal, plastic, ceramics, glass, paper, leather, etc.;

Third:It can integrat with other equipment on the pro:duction line ,and advance the automation degree of the production line;

Fourth: The symbol is clear, durable, beautiful, and prevent counterfeiting;

Fifth:Long service life and no pollution;

Sixth: Low working cost

The marking speed is fast and the symbol is formed at one time, the energy consumption is small, more important the work cost is low.

Seventh: High processing efficiency

The laser beam under the control of the computer ,so it can move at a high speed (speed up to 5 to 7 m/s), and the marking process can  complete with a few seconds. The printing of a standard computer keyboard can  finish in 12 seconds. The laser marking system is equipp a computer control system, which can actively cooperate with the high-speed assembly line.

Eighth:Fast development speed

Due to the connection between laser technology and accounting machine technology, users only need to program on the accounting machine to end the laser printing output, and can change the printing plan at any time, which fundamentally replaces the traditional mold making process, and shortens the product upgrade cycle and flexible production Provide convenience stuff.

Ninth: High machining accuracy

The laser can act on the surface of the material with a very thin beam, the smallest line width can reach 0.05mm. So it creates a broad application space for precision processing and increased anti-counterfeiting functions.

If you are interested in our laser welding machine. Please free feel to contact us.


WhatsApp: 0086 15264852794

The website:


Fiber laser cutting machine Martin

Fiber laser cutting machine Martin

Fiber laser cutting machine Martin

Hope everything become better and better. Hope the world more beautiful.

Martin from XT laser introduces fiber laser cutting machine here.

As the price of the Laser source becomes lower and lower. Fiber laser cutting machines become more popular on market. The cutting efficiency is very high compare to other cutting types.

On the market, people divide the laser cutting machine by power.

Firstly, there is a lower power fiber laser cutting machine. For this one, usually 1000-3000Watts.

Secondly, there is a middle power fiber laser cutting machine. For this one, usually 3000-6000Watts.

Thirdly, there is a high power fiber laser cutting machine. For this one, usually over 6000Watts.

Usually, we choose the power according to the thickness of the metal. But now many companies trend to purchase high power laser cutting machine. Especially in Europe and the Middle East.

The lower power fiber laser cutting machine usually is an open type. Like the picture show. If you need to cut sheet. You could choose this one. High quality but the price is really low. It also can improve your work efficiency.




Hope the above info lets you know more about XT LASER and machine.
More info you can contact me at any time:
WhatsApp&WeChat&Phone: +86 18612674468


Application of UV laser marking machine-Teresa

Application of UV laser marking machine

Glass is made of the fusion of silica and other chemicals.  (the main raw materials are soda ash, limestone, and quartz). And the silicate non-metallic material that gradually increases in viscosity and hardens to crystallize during cooling. As a synthetic material, it exudes a serene and pure taste, showing the beauty of form and reality, the beauty of light and shadow, the beauty of imagery, the beauty of time and space and the beauty of fun. The glass is beautiful, but it is not enough.

Therefore, designers use various tools to paint on the glass to add color to the glass products. UV laser marking machine surpasses the traditional processing, making up for various deficiencies in the past, such as low processing accuracy, difficult drawing, damaged workpieces, and environmental pollution. With its unique processing advantages, it has become a new favorite in the processing of glass products. The industry includes essential processing tools.

UV laser marking machine belongs to the series of laser marking machines, but it is developed using a 355nm ultraviolet laser . The machine uses third-order intra-cavity frequency doubling technology to compare with infrared laser . The 355 ultraviolet light spot is extremely small. And it can be to a large extent reduce the mechanical deformation of the material and the processing heat effect is small. Because it is mainly use for ultra-fine marking and engraving. Especially suitable for marking food, medical packaging materials, micro-holes, high-speed division of glass materials and silicon Application areas such as complex wafer cutting of wafers.

Advantage of UV laser marking machine:

First, UV laser marking machine is equipped with imported violet laser , which has excellent performance, uniform laser power density, fine light spot, and stable output optical power;

Secondly, the modular design of the UV laser marking machine is flexible in application. And it equipped with automatic/manual working mode;

Thirdly, UV laser marking machine has a wide range of applicable materials to make up for the lack of infrared laser processing capabilities, and can achieve ultra-fine laser marking;

Fourthly, UV laser marking machine has a small heat-affected zone. It can help to avoid damage by processed materials and a high yield rate;

Fifthly, UV laser marking machine does not need consumables. And the use cost and maintenance cost are low.

In the application of glass marking, UV laser marking machine has more advantage compared with CO2 laser marking machine. It’s marking effective is better. Its narking speed is faster. Its marking precision is more higher.

Different national languages, font styles, patterns, and laser marking techniques are handy. Due to the combination of laser marking technology and CNC system, after drawing on the computer, the ultraviolet laser marking machine can mark the words or patterns you want to say on the product, showing the casual romance.

For more information, please feel free to contact us.


Whatsapp: +8615006829603

Skype: xtlaser Teresa

keyboard laser marking machine-Jill

keyboard laser marking machine

We have many customers buy laser engraving machine to mark on keyboard.But many customers  still do not  how to choose suitable keyboard laser engraving machine.We would share more info in this article.

1.First,as for the machine model

In the laser marking machinemarket,there is mini portable,mini-enclosed,desktop model.Euraopean customers would like to choose mini-enclosed model.Indian customers would liek to choose desktop model.Besides,mini portable is the best seller.With small size,it can save room and shipping cost.

2.Secondly,as for the laser type

We suggest the fiber laser,which is socially used in the keyboard industry.

As for fiber,there are two kinds:fiber Raycus and fiber mopa

3.How to choose?fiber is better ?or mopa?

In order to give best suggestion,when u buy the machine,u need to tell us the keyboard info

1)Waht is the keyboard brand? 2)laptop or desktop?  3)Black,white or silver color?  4)backlight or not?

Especially for keyboard marking,there are many kinds of materials.Different material,different marking result.

4.Raycus for backlight Max keyboard

If ur keyboard is only backlight model,such as Mac Air A1466,etc.30w or 50w Raycus is okay.50w with 300*300mm lens is the best choice.If budget is not enough,30w is also okay,but as for 30w with 300*300mm lens ,the marking speed would be a little slow.

Here share u the videos

Raycus for Mac:

5.Mopa for others

Besides that,mopa is the best choice for u.Especially when u want to mark white color on black color.If u want to use Raycus,the marking effect may be a little with gray or yellow color,instead of white.Acccording to our experience ,30wmopa can achieve a good outcome.

If use Raycus,here is the video:

U can see,the effect is not good with yellow color

If use mopa,here is the video:

6.Difference between Raycus and mopa

In order to let you know more about the mopa and Raycus laser,here share you the difference:
MOPA laser and Raycus or IPG laser are both 1064nm wavelength laser beam.
1)MOPA laser source is Pulse width (2ns-250ns)  and Pulse frequency (1-1000HZ) , so MOPA laser is more flexible.
2)Raycus laser is Normal Q-Switched laser source,  Pulse width and pulse frequency are fixed, can not be changed.
Pulse width 90-130 ns,repetition frequency 30-100 kHz.

When marking on the plastics,such as pvc and keyboard,the mopa effect is more delicate and can not make the black plastic become yellow and gray.
That’s why we suggest you mopa marking machine.

More questions ask us freely

Jill from XT LASER

WhatsApp:+86 130 4603 3839

How to check the laser machine runing well-Wendy

How to check the laser machine runing well

How to check the laser machine runing well

How to check the laser is normal

When using the laser cutting machine,sometimes the laser cutting machine does not emit light. When such a fault occurs, the first thing to do is to check the machine.

1. Check whether the water is alternated normally, so that the water alternates normally. If the water protection is broken, the water supply can be short-circuited;

2, point pre-adjustment, see if the ammeter swings, if not swing, use the meter to measure whether the laser power supply has 220v power, if there is no light, there may be power failure, need to change;

3. It is also possible to check whether the ground wire and water protection test water on the power supply are bad, check the output power, and if the light is out, the potentiometer is broken and needs to be changed;

4. If the main program does not emit light, the machine card can use the meter to measure 15 (H) or 16 (L) angles and 14 degrees between the 14 corners. If there is any, the card is normal, there is no possible card. The signal has a problem;

5, there is a sound inside the laser power supply, usually the power connector does not touch, re-weld or connect, and then blow the dust inside the power supply.

First, check whether the fiber laser cutting machine water tank alarm.

Second, whether the fiber laser cutting machine emits light.

After you get the machine,if you have any questions of operation,do not worry.

We have the online service engineers to support you.

So if you want to buy machine,contact us.



Fiber laser air cutting process transformation solution-Wendy

Fiber laser air cutting process transformation solution

Now fiber laser cutting machine is good selling. we have many customers want to use the air cutting. So high pressure compresses air cutting process transformation solution.

1. Original reason:
Nitrogen (≦1.4MPa) mainly use for cutting stainless steel materials to ensure the stainless steel color of the cut section. Generally, the negative focus cutting is used when cutting thicker plates to obtain the best cutting effect. The best effect is to cut the stainless steel sheet. ,Good quality;
Oxygen (≦1MPa) mainly cuts carbon steel materials. And generally uses positive focus cutting when cutting thicker plates to obtain the best cutting effect;
The cutting performance of compressed air (≦0.8MPa) is poor, but the applicability is good.
Pressurized compressed air (medium and low pressure 1.4 – 1.6MPa) can cut stainless steel material. Then the cutting section is black and slightly yellow, the texture is fine. And can also cut carbon steel material, the cutting section is not much different than cutting with oxygen. But cutting The speed is a little bit more diffuse, not very obvious.
2. Pressurize compressed air cutting features: low cost, yellow cross section, large air pressure, and improve cutting capacity.

3. Advantages:

Mainly to save production costs. A single consumption of 80 kWh per day (1 yuan / KW / h), equivalent to 15 bottles (25 yuan / bottle) of oxygen working hours. Save more than 70,000 yuan / Taiwan. And can effectively improve the cutting ability and increase the cutting thickness.

4. Quality:

Compared with oxygen, the slag is slightly more and the speed is slightly longer. But the difference is not obvious. It can be distinguished by the naked eye and basically does not affect the use.
5. Negative focus cutting use regardless of the material.
6. The total investment is 75,000
7. Installation and commissioning time: 1 day

8. Process solution:

Primary compression (≧0.6MPa/2m3/h)→ storage (≧0.8MPa/2m3)→ one-time filtration→secondary filtration→first-stage drying→three-time filtratio. And then four-time filtration→secondary drying→increase Pressure treatment → Storage (≧1.4MPa/1m3)→ Flow valve→ Pipeline output. (can support 3 fiber laser cutting machines to work at the same time, cut with nitrogen process parameters, the speed adjustment can be slightly lower.)

9. Safety requirements:

The pressure resistance of each component is 2.0MPa. The safety valve: pressure relief when the pressure is MPa1.8MPa. The fixed connection of each interface. The pipeline needs to be leakproof and explosionproof.